Density of minerals
Specified practical 2 · F1 Elements, minerals and rocks · Spec F1.1e
Aim: Measure the density of minerals by finding their mass on a balance and their volume by displacement of water.
Do it in the virtual lab: choose the kit, plan the method, take your own readings, then use your results and answer exam questions. Every run gives new readings.
Revise this practical
Equipment
Show the kit
- Mineral specimens: The minerals whose density you are measuring.
- Top-pan balance: Measures the mass of each dry specimen (to 0.1 g).
- Measuring cylinder: Measures the volume of water the specimen pushes aside (displaces).
- Cotton thread: Lowers the specimen gently into the water so it does not crack the cylinder or splash.
- Dropping pipette: Tops the water up to an exact starting mark.
Method
Show the method
- Measure the mass of the dry specimen on a top-pan balance.
- Half fill a measuring cylinder with water and read the volume at the bottom of the meniscus.
- Tie the specimen to a thread and lower it gently until it is fully under the water.
- Read the new volume at eye level.
- Work out the volume of the specimen: new reading minus first reading.
- Repeat three times, then work out density = mass ÷ volume and find the mean.
The variables
What is the independent variable?
Show answer
The mineral being tested
You choose which mineral to test.
What is the dependent variable?
Show answer
The density, worked out from the mass and the volume
Density is the result you find.
Which of these is a control variable?
Show answer
Reading the meniscus at eye level every time, with the specimen fully under water
Reading the scale the same way each time keeps the volumes comparable.
Remember
- Density = mass ÷ volume (g/cm³). Volume of an irregular specimen = rise in the water level when it is fully submerged.
- Read the bottom of the meniscus at eye level. Two readings at ±0.5 cm³ give ±1.0 cm³ on the volume.
- Repeat and take a mean. Larger specimens give a smaller percentage uncertainty.
- Typical densities: quartz 2.65, calcite 2.7, barite 4.5, haematite 5.3, galena 7.5 g/cm³.
- Density helps identify ore minerals, which are usually much denser than the rock-forming silicates.
Exam-style questions
Why does a larger specimen give a more accurate density?
Show answer
It displaces more water, so the reading uncertainty is a smaller percentage of the volume
The ±1 cm³ uncertainty matters much less in 40 cm³ than in 5 cm³.
Why must there be no air bubbles stuck to the specimen?
Show answer
They add to the volume displaced, so the density comes out too low
Bubbles push the water level up, so the volume reads too high and mass ÷ volume is too small.
A pale mineral has a mass of 90 g and displaces 20 cm³ of water. Which mineral is it most likely to be?
Show answer
Barite
90 ÷ 20 = 4.5 g/cm³, the density of barite. A pale mineral this dense is almost certainly barite.
Play next
- 🧪 Next: Identifying unknown mineralsSpecified practical 3. Test unknown minerals and use a classification key to identify them.
- 🧪 Previous: Diagnostic properties of mineralsSpecified practical 1. Test known minerals for colour, lustre, streak, hardness, cleavage and reaction with acid, and record the results.
- 🧪 All Eduqas A-level Geology practicalsDo all 20 specified practicals (SP1 to SP20), plus extra ones for the other topics: kit, method, results and exam questions.
- ❓ Ten question quiz: Eduqas revision gameTen quick questions from one topic or a whole course.
- ✏️ Crosswords: Eduqas revision gameFive per topic. Fill in the grid, then check your answers.
- 🃏 Pairs: Eduqas revision gameMatch each question card to its answer card. Pick your topics, how many cards and how hard.
- 🗂️ Eduqas A-level Geology revisionEvery topic, with questions and answers, quizzes and crosswords.
