Wind speed and turbine power
Extra practical · 3.3 Energy resources · Spec 3.3.2, 3.3.4.1
Aim: Find how the power output of a model wind turbine depends on wind speed, and work out its efficiency.
Do it in the virtual lab: choose the kit, plan the method, take your own readings, then use your results and answer exam questions. Every run gives new readings.
Revise this practical
Equipment
Show the kit
- Model wind turbine: Its generator turns the kinetic energy of the wind into electrical energy.
- Electric fan with speed settings: Makes a steady wind at different speeds.
- Anemometer: Measures the wind velocity at the turbine.
- Voltmeter: Measures the p.d. across the load resistor (in parallel).
- Ammeter: Measures the current (in series).
- Ruler: Measures the blade length, to work out the swept area.
Method
Show the method
- Set the turbine a fixed distance in front of the fan, facing straight into it.
- Connect the generator to a load resistor with an ammeter in series and a voltmeter in parallel.
- Switch on the fan at the lowest setting and measure the wind velocity at the turbine with the anemometer.
- Wait for the blades to reach a steady speed, then record the p.d. and current.
- Repeat at each fan setting, then repeat the whole set and take means.
- Calculate the power output (P = V × I) and plot it against wind velocity cubed.
The variables
What is the independent variable?
Show answer
Wind velocity
You change the fan setting.
Which is a control variable?
Show answer
The distance and angle between fan and turbine
Also keep the blade angle and the load resistor the same.
Why measure the wind velocity at the turbine, not at the fan?
Show answer
The air slows and spreads out between the fan and the turbine
The turbine only gets the wind that reaches it.
Remember
- Power in the wind = ½ρAv³ (ρ = air density, A = swept area = π r², v = wind velocity).
- Power output P = V × I; P ∝ v³, so doubling wind velocity gives about 8 times the power.
- Efficiency = power out ÷ power in × 100. Capacity factor = actual output ÷ maximum possible output.
- Measure wind velocity at the turbine with an anemometer; keep distance, angle and load the same.
Exam-style questions
A 2 MW turbine produced 5256 MWh in a year (8760 hours). What is its capacity factor?
Show answer
30%
5256 ÷ (2 × 8760) × 100 = 30%: the wind does not always blow at the rated speed.
Why are wind farms often built offshore?
Show answer
Wind velocities are higher and steadier, and there is less visual impact
Offshore turbines cost more to build and connect to the grid.
Why can no turbine capture all the energy in the wind?
Show answer
The air must keep moving past the blades, so it keeps some kinetic energy
The theoretical maximum (the Betz limit) is about 59%.
Play next
- 🧪 Next: Energy from biofuels and fossil fuelsExtra practical. Burn bioethanol, biodiesel and paraffin to heat water, and compare the energy each releases per gram.
- 🧪 Previous: Infiltration rate and tramplingExtra practical. Measure the infiltration rate of soil on a footpath and on nearby grassland, and test the difference with a t-test.
- 🧪 All AQA A-level Environmental Science practicalsPractise every sampling technique (ST1 to ST6) and the statistics: kit, method, readings and exam questions.
- ❓ Ten question quiz: AQA revision gameTen quick questions from one topic or a whole course.
- ✏️ Crosswords: AQA revision gameFive per topic. Fill in the grid, then check your answers.
- 🃏 Pairs: AQA revision gameMatch each question card to its answer card. Pick your topics, how many cards and how hard.
- 🏝️ KN Island: revision gameRun an island for 12 years (14 in Examiner mode): every choice is real Environmental Science.
- 🔗 Associations: AQA revision gameLink eight key terms on a board and say why each pair goes together.
- 5️⃣ Five Degrees: AQA revision gameGet from one term to another in five steps or fewer, with a link that makes sense at every step.
- 🗂️ AQA A-level Environmental Science revisionEvery topic, with questions and answers, quizzes and crosswords.
