Specific heat capacity
Required practical 1 · 4.1 Energy · Spec 4.1.1.3
Aim: Find the specific heat capacity of a metal block by heating it and measuring how fast its temperature rises.
Do it in the virtual lab: choose the kit, plan the method, take your own readings, then use your results and answer exam questions. Every run gives new readings.
Revise this practical
Equipment
Show the kit
- 1 kg metal block: The material you are testing. It has holes for the heater and thermometer.
- Immersion heater: Transfers energy to the block electrically, so you can work out the energy from V, I and t.
- Power supply: Runs the heater (about 12 V).
- Ammeter: Measures the current through the heater (in series).
- Voltmeter: Measures the potential difference across the heater (in parallel).
- Thermometer: Measures the temperature of the block.
- Stopwatch: Times the heating so you can work out the energy transferred.
- Top-pan balance: Measures the mass of the block.
- Insulation: Wrapped round the block to cut the energy lost to the surroundings.
Method
Show the method
- Measure the mass of the metal block on a top-pan balance.
- Put the heater and thermometer into the holes in the block and wrap the block in insulation.
- Connect the heater to the power supply with an ammeter in series and a voltmeter in parallel.
- Record the starting temperature, then switch on and start the stopwatch.
- Record the temperature, current and potential difference every minute for 10 minutes.
- Work out the energy transferred (E = V × I × t) and use it to calculate the specific heat capacity.
The variables
What is the independent variable?
Show answer
The energy transferred (set by the heating time)
You choose how long to heat for, and that sets how much energy is transferred.
What is the dependent variable?
Show answer
The temperature of the block
You measure how much the temperature rises.
Which of these is a control variable?
Show answer
The mass of the block
Keep the mass the same (1 kg) so the test is fair.
Remember
- Specific heat capacity: the energy needed to raise the temperature of 1 kg of a substance by 1 °C.
- ΔE = m × c × Δθ, so c = ΔE ÷ (m × Δθ). Energy from the heater: E = V × I × t (or read a joulemeter).
- Ammeter in series with the heater, voltmeter in parallel across it.
- Your value is usually too high because energy is lost to the surroundings: insulate the block.
- On a temperature against energy graph, the gradient = 1 ÷ (m × c).
Exam-style questions
How could you reduce energy losses from the block?
Show answer
Wrap the block in more insulation and put oil in the thermometer hole
Insulation cuts energy lost to the surroundings. A drop of oil in the hole helps the thermometer read the block’s temperature.
Why does the temperature carry on rising for a short time after the heater is switched off?
Show answer
The heater is still hotter than the block and keeps transferring energy
The heater takes time to cool down, and it keeps heating the block.
What is the main hazard and how do you control it?
Show answer
The heater and block get hot: do not touch them until they have cooled
The heater can burn you. Let it cool on a heatproof mat before you move it.
Play next
- 🧪 Next: Thermal insulationRequired practical 2. Compare how well different materials keep a beaker of hot water warm.
- 🧪 All AQA GCSE Physics practicalsDo all ten required practicals, plus extra ones for each topic: kit, method, readings and exam questions.
- ❓ Ten question quiz: AQA revision gameTen quick questions from one topic or a whole course.
- ✏️ Crosswords: AQA revision gameFive per topic. Fill in the grid, then check your answers.
- 🃏 Pairs: AQA revision gameMatch each question card to its answer card. Pick your topics, how many cards and how hard.
- 🗂️ AQA GCSE Physics revisionEvery topic, with questions and answers, quizzes and crosswords.
