Plotting features on a base map
Specified practical 12 · F2 Surface and internal processes of the rock cycle · Spec F2.3b
Aim: Locate geological features in the field by compass bearing and pacing, then plot them on a 1:10 000 base map.
Do it in the virtual lab: choose the kit, plan the method, take your own readings, then use your results and answer exam questions. Every run gives new readings.
Revise this practical
Equipment
Show the kit
- Base map: A 1:10 000 map with roads, walls and buildings but no geology yet.
- Compass: Gives the bearing from a known point to each feature.
- Tape measure: Measures out 50 m so you can find the length of your pace.
- Protractor: Plots each bearing on the map.
- Ruler: Measures the distance on the map.
- Pencil: Marks and labels the features on the map.
Method
Show the method
- Measure your pace length: walk a taped 50 m and count your paces.
- Stand at a point you can find exactly on the map, such as a wall corner.
- Take a compass bearing from that point to the feature.
- Pace the distance to the feature and turn the paces into metres.
- Turn the distance in metres into a map distance using the scale.
- Plot the feature with a protractor and ruler, then label it with a symbol.
Planning questions
Why measure your own pace length first?
Show answer
Pace lengths differ between people and on slopes, so paces must be turned into metres accurately
Calibrating your pace on 50 m of tape makes your distances reliable.
Why start from a point you can find exactly on the map?
Show answer
Any error in the starting point moves every feature plotted from it
A precise known point means the bearing and distance place the feature correctly.
How could you check a plotted position?
Show answer
Take a second bearing from another known point: where the lines cross is the position
Two crossing bearings (triangulation) fix a position more reliably than one.
Remember
- Calibrate your pace on a measured distance; distance = paces × pace length.
- Take bearings from a precise known point; check with a second bearing (triangulation) or a back bearing (± 180°).
- 1:10 000 → 1 mm on the map = 10 m on the ground. 1:25 000 → 1 mm = 25 m.
- Show observed boundaries as solid lines and inferred ones as dashed lines.
Exam-style questions
On a 1:10 000 map, a fault is 23 mm from a road. How far is that on the ground?
Show answer
230 m
1 mm = 10 m, so 23 mm = 230 m.
What is a back bearing used for?
Show answer
Finding your own position from a feature you can see on the map
The back bearing is the bearing ± 180°: draw it from the known feature to find where you are.
Why do mapped boundaries often have dashed lines?
Show answer
Dashed lines show where a boundary is inferred, not seen at an exposure
Solid = seen (observed); dashed = inferred between exposures.
Play next
- 🧪 Next: Six-figure grid referencesSpecified practical 13. Find geological features in the field and record their six-figure grid references on a map.
- 🧪 Previous: Metamorphic rocks in thin sectionSpecified practical 11. Use photomicrographs of metamorphic rocks to identify their minerals and textures, then work out the temperature and pressure they formed at.
- 🧪 All Eduqas A-level Geology practicalsDo all 20 specified practicals (SP1 to SP20), plus extra ones for the other topics: kit, method, results and exam questions.
- ❓ Ten question quiz: Eduqas revision gameTen quick questions from one topic or a whole course.
- ✏️ Crosswords: Eduqas revision gameFive per topic. Fill in the grid, then check your answers.
- 🃏 Pairs: Eduqas revision gameMatch each question card to its answer card. Pick your topics, how many cards and how hard.
- 🗂️ Eduqas A-level Geology revisionEvery topic, with questions and answers, quizzes and crosswords.
