Identifying ions
Required practical 7 · 4.8 Chemical analysis · Spec 4.8.3
Aim: Use flame tests and chemical tests to identify the positive and negative ions in six unknown salts.
Do it in the virtual lab: choose the kit, plan the method, take your own readings, then use your results and answer exam questions. Every run gives new readings.
Revise this practical
Equipment
Show the kit
- Nichrome wire loop: Picks up a little solid for the flame test.
- Bunsen burner: A blue flame for the flame tests.
- Test tubes: For the precipitate tests.
- Sodium hydroxide solution: Gives coloured precipitates with many metal ions.
- Silver nitrate and barium chloride solutions (with dilute acids): Tests for halide and sulfate ions.
- Limewater: Turns milky with carbon dioxide from a carbonate.
- Safety goggles: Several of the reagents are corrosive or toxic.
Method
Show the method
- Dip a clean nichrome loop into the solid, hold it in the edge of a blue Bunsen flame and note the colour.
- Dissolve some of the salt in water and put a little into three test tubes.
- Add a few drops of sodium hydroxide solution to the first tube and look for a precipitate.
- Add dilute hydrochloric acid to a little of the solid and bubble any gas through limewater.
- Add dilute nitric acid then silver nitrate solution to the second tube.
- Add dilute hydrochloric acid then barium chloride solution to the third tube.
The variables
Why clean the wire loop between flame tests?
Show answer
So no trace of the last metal changes the flame colour
Dip it in acid and heat it until it gives no colour.
Why add dilute nitric acid before silver nitrate?
Show answer
To remove carbonate ions, which would also give a precipitate
Do not use hydrochloric acid here: it adds chloride ions.
Which flame colour shows potassium ions?
Show answer
Lilac
Lithium crimson, sodium yellow, potassium lilac, calcium orange-red, copper green.
Remember
- Flame tests: Li⁺ crimson, Na⁺ yellow, K⁺ lilac, Ca²⁺ orange-red, Cu²⁺ green.
- NaOH: Cu²⁺ blue, Fe²⁺ green, Fe³⁺ brown, Ca²⁺/Mg²⁺/Al³⁺ white (Al³⁺ dissolves in excess).
- Carbonate: fizzes with acid, CO₂ turns limewater milky.
- Halides: nitric acid + silver nitrate: chloride white, bromide cream, iodide yellow.
- Sulfate: hydrochloric acid + barium chloride: white precipitate.
Exam-style questions
What do iron(III) ions give with sodium hydroxide solution?
Show answer
A brown precipitate
Iron(II) gives green; copper(II) gives blue.
Why might a flame test fail to identify the metals in a mixture?
Show answer
One flame colour can hide (mask) another
For example, a strong yellow sodium flame masks others.
Why is flame emission spectroscopy better than a flame test?
Show answer
It can identify ions in mixtures and measure their concentration
Instrumental methods are accurate, sensitive and rapid.
Play next
- 🧪 Next: Oxygen in the airExtra practical. Measure the percentage of oxygen in air, using damp iron wool that uses up oxygen as it rusts.
- 🧪 Previous: ChromatographyRequired practical 6. Use paper chromatography to separate the dyes in an unknown ink, identify them and work out their Rf values.
- 🧪 All AQA GCSE Chemistry practicalsDo all eight required practicals, plus extra ones for each topic: kit, method, readings and exam questions.
- ❓ Ten question quiz: AQA revision gameTen quick questions from one topic or a whole course.
- ✏️ Crosswords: AQA revision gameFive per topic. Fill in the grid, then check your answers.
- 🃏 Pairs: AQA revision gameMatch each question card to its answer card. Pick your topics, how many cards and how hard.
- 🗂️ AQA GCSE Chemistry revisionEvery topic, with questions and answers, quizzes and crosswords.
